Osciloscopio Hantek Dso5202p Digital Oscilloscope 200MHz Bandwidth 2 Channels Handheld LCD USB Multimetro

• Customization: Available
• After-sales Service: Yes
• Warranty: 1 Year
• Model NO.: DSO5202P
• Kind: Digital Oscilloscope
• Channel Number: 2
• Structure: Desktop
• Application: Frequency Measurement
• Bandwidth: >1GHz
• Trigger Modes: Automatic
• Deeper Memory Depth: 140Mpts
• Sampling Rate: 1GSa/s
• Brandwidth: 200MHz
• Transport Package: Carton Package
• Origin: China
• HS Code: 9031499090
• Production Capacity: 50000piece/Month

Product Description

Osciloscopio Hantek DSO5202P Digital Oscilloscope 200MHz bandwidth 2 Channels Handheld LCD USB Multimetro

200M bandwidths

1GSa/s Real Time sample rate
Large (7.0-inch) color display,WVGA(800x480)

Record length up to 24K
Trigger mode: edge/pulse width/line selectable video/slop/overtime etc.
USB host and device connectivity, standard
Multiple automatic measurements
Four math functions, including FFTs standard

Provides software for PC real-time analysis

 

Model	DSO5202P	DSO5102P	DSO5072P
Acquisition
Sample Rate	Real-Time Sample: 1GS/s
	Equivalent Sample: 25GS/s
Acquisition Modes
Normal	Normal data only
Peak-Detect	High-frequency and randon glith capture
Average	Wavefom Average, selectable 4,8,16,32,64,128
Inputs
Inputs Coupling	AC, DC, GND
Inpits Impendance	1MΩ±2% II20pF±3pF
Probe Attenuation	1X, 10X
Supported Probe Attenuation Factor	1X, 10X, 100X, 1000X
Maximum Input Voltage	CAT I and CAT II: 300VRMS (10×), Installation Category;
	CAT III: 150VRMS (1×);
	Installation Category II: derate at 20dB/decade above 100kHz to 13V peak-AC at 3MHz* and above.
	For non-sinusoidal waveforms, peak-value must be less than 450V.
	Excursion above 300V should be of less than 100ms duration.
	RMS signal level including all DC components removed through AC coupling must be limited to 300V.
	If these values are exceeded, damage to the oscilloscope may occur.
Horizontal
Sample Rate Range	500MS/s--1GS/s
Waveform Interpolation	(sin x)/x
Record Length	40 K
SEC/DIV Range	4ns/div to 40s/div	4ns/div to 40s/div
Sample Rate and	±50ppm(at over any ≥1ms time interval)
Delay Time Accuracy
Position Range	2ns/div to 10ns/div;	20ns/div to 80us/div; (-8div x s/div) to 40ms;
	(-4div x s/div) to 20ms;	200us/div to 40s/div; (-8div x s/div) to 400s
Delta-Time Measurement Accuracy	Single-shot, Normal mode:± (1 sample interval +100ppm × reading + 0.6ns);
(Full Bandwidth)	>16 averages:± (1 sample interval + 100ppm × reading + 0.4ns);
	Sample interval = s/div ÷ 200
Vertical
Vertical Resolution	8-bit resolution, all channel sampled simultaneously
Position Range	2mV/div to 200mV/div, ±2V
	200mV/div to 5V/div, ±50V
Bandwidth	100MHz	100MHz	70MHz
Rise Time at BNC( typical)	3.5ns	3.5ns	5ns
Analog Bandwidth in Normal and	2mV/div to 20mV/div, ±400mV; 50mV/div to 200mV/div, ±2V
Average modes at BNC or with probe, DC Coupled	500mV/div to 2V/div, ±40V; 5V/div, ±50V
Math	+, -, *, /, FFT
FFT	Windows: Hanning, Flatop, Rectamgular, Bartlett, Blackman;
	1024 sample point
Bandwidth Limit	20MHz
Low Frequency Response (-3db)	≤10Hz at BNC
DC Gain Accuracy	±3% for Normal or Average acquisition mode, 5V/div to 10mV/div;
	±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div
DC Measurement Accuracy,	When vertical displacement is-zero, and N ≥16:± (3% × reading + 0.1div + 1mV) only 10mV/div or greater is selected;
Average Acquisition Mode	When vertical displacement is not-zero, and N≥16: ± [3% × (reading + vertical position) + 1% of vertical position + 0.2div];
	Add 2mV for settings from 2mV/div to 200mV/div; add 50mV for settings from 200mV/div to 5V/div
Volts Measurement Repeatability,	Delta-volts between any two averages of ≥16 waveforms acquired under same setup and ambient conditions
Average Acquisition Mode
Trigger System
Trigger Types	Edge,Video, Pulse, Slope, Over time, Alternative
Trigger Source	CH1, CH2, EXT, EXT/5, AC Line
Trigger Modes	Auto, Normal, Single
Coupling Type	DC, AC, Noise Reject, HF Reject, LF Reject
Trigger Sensitivity	DC(CH1,CH2):
(Edge-Trigger Type)	1div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full;
	DC(EXT):
	200mV from DC to 100MHz; 350mV from 100MHz to 200MHz;
	DC(EXT/5):
	1V from DC to 100MHz;1.75V from 100MHz to 200MHz;
	AC: Attenuates signals below 10Hz;
	HF Reject: Attenuates signals above 80kHz;
	LF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHz
Trigger Level Range	CH1/CH2: ±8 divisions from center of screen;
	EXT: ±1.2V;
	EXT/5:±6V
Trigger Level Accuracy( typical)Accuracy	CH1/CH2: 0.2div × volts/div within ±4 divisions from center of screen;
is for signals having rise and fall times ≥20ns	EXT: ± (6% of setting + 40mV);
	EXT/5: ± (6% of setting + 200mV);
Set Level to 50%(typical)	Operates with input signals ≥50Hz
Video Trigger
Video Trigger Type	CH1, CH2: Peak-to-peak amplitude of 2 divisions;
	EXT: 400mV;
	EXT/5: 2V
Signal Formats and Field Rates, Video Trigger Type	Supports NTSC, PAL and SECAM broadcast systems for any field or any line
Holdoff Range	100ns ~ 10s
Pulse Width Trigger
Pulse Width Trigger Mode	Trigger when (< , >, = , or ≠); Positive pulse or Negative pulse
Pulse Width Trigger Point	Equal: The oscilloscope triggers when the trailing-edge of the pulse the trigger level.
	Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing-edge.
	Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width.
	Less than: The trigger point is the trailing-edge.
	Greater than (also called overtime trigger): The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width
Pulse Width Range	20ns ~ 10s
Slope Trigger
Slope Trigger Mode	Trigger when (< , > , = , or ≠ ); Positive slope or Negative slope
Slope Trigger Point	Equal: The oscilloscope triggers when the waveform slope is equal to the set slope.
	Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope.
	Less than: The oscilloscope triggers when the waveform slope is less than the set slope.
	Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope.
Time Range	20ns ~ 10s
Overtime Trigger
Over Time Mode	Rising-edge or Falling-edge
Time Range	20ns ~ 10s
Alternative Trigger
Trigger on CH1	Internal Trigger:-Edge, Pulse Width, Video, Slope
Trigger on CH2	Internal Trigger:-Edge, Pulse Width, Video, Slope
Trigger Frequency Counter
Readout Resolution	6 digits
Accuracy (typical)	±30ppm (including all frequency reference errors and ±1 count errors)
Frequency Range	AC coupled, from 4Hz minimum to rated bandwidth
Signal Source	Pulse Width or Edge Trigger modes: all available trigger sources
	The Frequency Counter measures trigger source at all times, including when the oscilloscope acquisition pauses
	due to changes in the run status, or acquisition of a single shot event has completed.
	Pulse Width Trigger mode: The oscilloscope counts pulses of significant magnitude inside the 1s measurement window that qualify as triggerable events,
	such as narrow pulses in a PWM pulse train if set to < mode and the width is set to a relatively small time.
	Edge Trigger mode: The oscilloscope counts all edges of sufficient magnitude and correct polarity.
	Video Trigger mode: The Frequency Counter does not work.
Measure
Cursor Measurement	Voltage difference between cursors: ΔV
	Time difference between cursors: ΔT
	Reciprocal of ΔT in Hertz (1/ΔT)
Auto Measuerment	Frequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time, +Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF
Display
Display Type	7 inch 64K color TFT (diagonal liquid crystal)
Display Resolution	800 horizontal by 480 vertical pixels
Display Contrast	Adjustable (16 gears) with the progress bar
Probe Compensator Output
Output Voltage( typical)	About 5Vpp into ≥1MΩ load
Frequency(typical)	1kHz
Power Supply
Supply Voltage	100-120VACRMS(±10%), 45Hz to 440Hz, CATII
	120-240VACRMS(±10%), 45Hz to 66Hz, CATII
Power Consumption	<30W
Fuse	2A, T rating, 250V
Environmental
Temperature	Operating: 32F to 122F (0C to 50C);
	Nonoperating: -40F to 159.8F (-40C to +71C)
Cooling Method	Convection
Humidity	+104F or below (+40C or below): ≤90% relative humidity;
	106F to 122F (+41C to 50C): ≤60% relative humidity
Altitude	Operating: Below 3,000m (10,000 feet);
	Nonoperaring: Below 15,000m(50,000 feet)
Mechanical
Size	Length 385mm, Width 200mm, Height 245mm

 

 

 

FAQ

1. Are you a manufacturer or a trader?
Yes, we are both.
 
2. What products do you have?
We are focus on instruments and meters. Such as Mechanical /  Optical /Power/ SafetyEnvironmental testing equipments and
some hardware tools amd eletronic components.
More infomation about business, please contact us we can send you catalog for reference.

3. Can i get a sample first?
Yes, we are pleased to send you sample to test the quality and market.

4. Can you do OEM for us?
Yes, OEM are welcome for us. Customers' brand, logo, label can be customized for the produets andcarton package, but based on a certain quantity.

5. What are your strengths?
We have a complete range of products covering low, medium and high-end markets in good price in Instruments field.
Fast Delivery, factory high quality and professional engineers to solve your problems.